Inspect Your Trees
Inspect your trees every year. Tree inspections can be done at any time of year, leaf-on or leaf-off. To be thorough, inspect trees after leaf drop in fall, after leaf-out in spring, and routinely after severe storms. Inspect trees carefully and systematically. Examine all parts of the tree, including the roots, root or trunk flare, main stem, branches, and branch unions. Be sure to examine all sides of the tree. Use a pair of binoculars to see branches high off the ground. Consider the following factors when inspecting trees:
Tree Condition:
Trees in poor condition may have many dead twigs, dead branches, or small, off-color leaves. Trees in good condition will have full crowns, vigorous branches, and healthy, full-sized leaves; however, green foliage in the crown does not ensure that a tree is safe. Tree trunks and branches can be quite defective and still support a lush green crown. Tree Species: Certain tree species are prone to specific types of defects. For example, some species of maple and ash often form weak branch unions, and aspen is prone to breakage at a young age (50-70 years) due to a variety of factors, including decay and cankers.
Tree Age and Size:
Trees are living organisms subject to constant stress. Pay particular attention to older trees, which may have accumulated multiple defects and extensive decay.
What to Look For:
Hazardous defects are visible signs that the tree is failing. We recognize seven main types of tree defects: dead wood, cracks, weak branch unions, decay, cankers, root problems, and poor tree architecture. A tree with defects is not hazardous, however, unless some portion of it is within striking distance of a target. Dead wood Dead wood is “not negotiable”-- dead trees and large dead branches must be removed immediately! Dead trees and branches are unpredictable and can break and fall at any time. Dead wood is often dry and brittle and cannot bend in the wind like a living tree or branch. Dead branches and tree tops that are already broken off (“hangers” or “widow makers”) are especially dangerous!
Take immediate action if...
Poor Tree Architecture
Poor architecture is a growth pattern that indicates weakness or structural imbalance. Trees with strange shapes are interesting to look at, but may be structurally defective. Poor architecture often arises after many years of damage from storms, unusual growing conditions, improper pruning, topping, and other damage. A leaning tree may be a hazard. Because not all leaning trees are dangerous, any leaning tree of concern should be examined by a professional arborist.
Take action if...
Multiple Defects
The recognition of multiple defects in a tree is critical when evaluating the tree’s potential to fail. Multiple defects that are touching or are close to one another should be carefully examined. If more than one defect occurs on the tree’s main stem, you should assume that the tree is extremely hazardous.
Corrective Actions
Corrective actions begin with a thorough evaluation. If a hazardous situation exists, there are three recommended options for correcting the problem: move the target, prune the tree, or remove the tree.
Move the Target
Removing the target is often an inexpensive and effective treatment for correcting a hazard tree. Easily moved items like play sets and swings, RV's, and picnic tables can be placed out of the reach of the hazardous tree with little effort and expense. If the target cannot be moved and a serious hazard exists, consider blocking access to the target area until the hazard can be properly eliminated.
Tree Condition:
Trees in poor condition may have many dead twigs, dead branches, or small, off-color leaves. Trees in good condition will have full crowns, vigorous branches, and healthy, full-sized leaves; however, green foliage in the crown does not ensure that a tree is safe. Tree trunks and branches can be quite defective and still support a lush green crown. Tree Species: Certain tree species are prone to specific types of defects. For example, some species of maple and ash often form weak branch unions, and aspen is prone to breakage at a young age (50-70 years) due to a variety of factors, including decay and cankers.
Tree Age and Size:
Trees are living organisms subject to constant stress. Pay particular attention to older trees, which may have accumulated multiple defects and extensive decay.
What to Look For:
Hazardous defects are visible signs that the tree is failing. We recognize seven main types of tree defects: dead wood, cracks, weak branch unions, decay, cankers, root problems, and poor tree architecture. A tree with defects is not hazardous, however, unless some portion of it is within striking distance of a target. Dead wood Dead wood is “not negotiable”-- dead trees and large dead branches must be removed immediately! Dead trees and branches are unpredictable and can break and fall at any time. Dead wood is often dry and brittle and cannot bend in the wind like a living tree or branch. Dead branches and tree tops that are already broken off (“hangers” or “widow makers”) are especially dangerous!
Take immediate action if...
- A broken branch or top is lodged in a tree.
- A tree is dead.
- A branch is dead and of sufficient size to cause injury (this will vary with height and size of branch).
Cracks
A crack is a deep split through the bark, extending into the wood of the tree. Cracks are extremely dangerous because they indicate that the tree is already failing. Take action if... - A crack extends deeply into, or completely through the stem.
- Two or more cracks occur in the same general area of the stem.
- A crack is in contact with another defect.
- A branch of sufficient size to cause injury is cracked.
Weak Branch Unions
Weak branch unions are places where branches are not strongly attached to the tree. A weak union occurs when two or more similarly-sized, usually upright branches grow so closely together that bark grows between the branches, inside the union. This ingrown bark does not have the structural strength of wood, and the union is much weaker than one that does not have included bark. The included bark may also act as a wedge and force the branch union to split apart. Trees with a tendency to form upright branches, such as elm and maple, often produce weak branch unions.Weak branch unions also form after a tree or branch is tipped or topped, i.e., when the main stem or a large branch is cut at a right angle to the direction of growth leaving a large branch stub. The stub inevitably decays, providing very poor support for new branches (“epicormic” branches) that usually develop along the cut branch. Take action if... - A weak branch union occurs on the main stem.
- A weak branch union is cracked.
- A weak branch union is associated with a crack, cavity, or other defect.
Decay
Decaying trees can be prone to failure, but the presence of decay, by itself, does not indicate that the tree is hazardous. Advanced decay, i.e., wood that is soft, punky, or crumbly, or a cavity where the wood is missing can create a serious hazard. Evidence of fungal activity including mushrooms, conks, and brackets growing on root flares, stems, or branches are indicators of advanced decay. A tree usually decays from the inside out, eventually forming a cavity, but sound wood is also added to the outside of the tree as it grows. Trees with sound outer wood shells may be relatively safe, but this depends upon the ratio of sound to decayed wood, and other defects that might be present. Evaluating the safety of a decaying tree is usually best left to trained arborists. Take action if... - Advanced decay is associated with cracks, weak branch unions, or other defects.
- A branch of sufficient size to cause injury is decayed.
- The thickness of sound wood is less than 1" for every 6" of diameter at any point on the stem.
Cankers
A canker is a localized area on the stem or branch of a tree, where the bark is sunken or missing. Cankers are caused by wounding or disease. The presence of a canker increases the chance of the stem breaking near the canker (Fig. 5). A tree with a canker that encompasses more than half of the tree's circumference may be hazardous even if exposed wood appears sound. Take action if... - A canker or multiple cankers affect more than half of the tree's circumference.
- A canker is physically connected to a crack, weak branch union, a cavity, or other defect.
Root Problems
Trees with root problems may blow over in wind storms. They may even fall without warning in summer when burdened with the weight of the tree’s leaves. There are many kinds of root problems to consider, e.g., severing or paving-over roots; raising or lowering the soil grade near the tree; parking or driving vehicles over the roots; or extensive root decay. Soil mounding, twig dieback, dead wood in the crown, and off-color or smaller than normal leaves are symptoms often associated with root problems. Because most defective roots are underground and out of sight, aboveground symptoms may serve as the best warning.
Take action if... - A tree is leaning with recent root exposure, soil movement, or soil mounding near the base of the tree.
- More than half of the roots under the tree’s crown have been cut or crushed. These trees are dangerous because they do not have adequate structural support from the root system.
- Advanced decay is present in the root flares or “buttress” roots.
Poor Tree Architecture
Poor architecture is a growth pattern that indicates weakness or structural imbalance. Trees with strange shapes are interesting to look at, but may be structurally defective. Poor architecture often arises after many years of damage from storms, unusual growing conditions, improper pruning, topping, and other damage. A leaning tree may be a hazard. Because not all leaning trees are dangerous, any leaning tree of concern should be examined by a professional arborist.
Take action if...
- A tree leans excessively.
- A large branch is out of proportion with the rest of the crown.
Multiple Defects
The recognition of multiple defects in a tree is critical when evaluating the tree’s potential to fail. Multiple defects that are touching or are close to one another should be carefully examined. If more than one defect occurs on the tree’s main stem, you should assume that the tree is extremely hazardous.
Corrective Actions
Corrective actions begin with a thorough evaluation. If a hazardous situation exists, there are three recommended options for correcting the problem: move the target, prune the tree, or remove the tree.
Move the Target
Removing the target is often an inexpensive and effective treatment for correcting a hazard tree. Easily moved items like play sets and swings, RV's, and picnic tables can be placed out of the reach of the hazardous tree with little effort and expense. If the target cannot be moved and a serious hazard exists, consider blocking access to the target area until the hazard can be properly eliminated.
